• Supports Sensorless Three-Phase BLDC Motors. 3-Phase BLDC Motor. • Continuous Output Power up to 300W. • Continuous Power: 300W. • PWM Input • High Efficiency Aluminum Alloy Heat Sink Base. • Vacuum Cleaner Motors • High-Speed Blowers• RC Aircraft Motors.
Product Description Features:* Brand new and high quality* Made of high quality materials, sturdy and * MA MB MC phase line output is connected to the motor* 5V GND motherboard comes with 5V power supply (current does not exceed 30MA)* VCC GND motor main power supply (external DC power supply)* SC speed pulse signal output* Forward and reverse control interface (can also be connected to an external switch)* VR speed control signal input (the onboard potentiometer speed control can also be connected to 0-5V analog analog PWM duty cycle to support dual signal input speed control)* Ha Hb Hc +5V GND Hall signal power input. Generally, motors with Hall have five corresponding lines.Full patch process performance is stable with forward and reverse functionsTip:After receiving the goods, there are generally 5 Hall wiring lines on the brushless motor. Two of them are Hall power lines. Three Hall signal lines must be distinguished. In particular, the power cord must not be connected incorrectly. The three-phase line sequ ence on the board must be consistent with the three-phase line sequ ence on the motor drive board to work properly. If you dont know the definition of the Hall line, you can debug low voltage and low current when power is first applied. Change the order of the Hall wires until they work normally. Do not use high current or high voltage for debugging. If the Hall wires are not connected in order, there is a risk of damaging the MOS tube if the Hall wires are not connected in order. If the three Hall signal wires are used, the motor runs smoothly. ,smooth. Smooth start at low speed and high torque. If the three Hall signal wires are not connected, there are the following characteristics: 1. The motor cannot start normally or is difficult to start (sometimes it is necessary to manually turn the motor to start) 2. The motor starts to vibrate and is out of power.Motherboard specifications:Product name: 400W brushless Hall DC motor driverModel: ZS-X11D1Working voltage: 9-60VMaximum current: rated 16A, peak 20AMaximum power: 400WOvercurrent protection: yesProduct size: length 63MM*width 45MM*height 28MMWeight: approximately 93 grams.Precautions:1. The power supply circuit on the motherboard does not have a fuse, and the built-in self-energization will cause permanent damage to the chip on the board (not even allowed for 2 seconds).2. During normal , the motor output has sampling overcurrent protection. Since the module has high power and current, please do not short-circuit the module when it is not working properly. In the event of a short circuit, there is a possibility of wire burnout. Please use a small current and low voltage test for the first wiring test. After the test is OK, use a large current and high voltage. Because it is a bare board module sold, pay attention to the insulation of the wiring line and do not allow strong voltage to contact the board. parts.3. Do not connect a motor whose voltage and current are obviously inconsistent with the drive module or which is far away from the motor to avoid inexplicable damage.Package Included:1 x Brushless Motor Controller1 x connecting cableNote: 1.The real color of the item may be slightly different from the pictures shown on website caused by many factors such as brightness of your monitor and light brightness.2.Please allow slight manual measurement deviation for the data.Payment Payment must be completed within 5 days. If you have any problems about payment, please contact us via ebay message.Delivery details We only ship to confirmed ebay Order addresses. Please comfirm that your Order address is in line with your shipping address. Please kindly note that the combined shipping is not provided because the shipping fee is calculated by weight. Also, the each additional item means exactly the the same color and size. It takes about 7-15 working days to US; about 10-30 working days to other countries. Transit time may be a little delayed because of the bad weather and customs inspection. If you do not receive your item within 30 working days since payment finished, please contact us immediately for further assistance. Contact us We strive for 100% customer satisfaction! Positive Feedback is very important to us. If you have any questions, please feel free to contact us via “Ask seller a question” . We will reply your email within 24 working hours.
About Product:1.MA MB MC phase line output connection motor2. 5V GND motherboard comes with 5V power supply (current does not exceed 30MA)3.VCC GND motor main power supply (external DC power supply)4.SC speed pulse signal output5 positive and negative reversing control interface (also can be connected to the external switch)6.VR speed control signal input (onboard with potentiometer speed control can also be connected to 0-5V analog simulation PWM duty cycle to support dual signal input speed regulation)7.Ha Hb Hc +5V GND Hall signal Power input, generally with Hall’s motor has five corresponding linesFull patch process Stable performance with positive/reverse function Tips:After receiving the goods, there are generally 5 Hall wiring lines on the brushless motor. Two of them are the Hall power supply lines. The three Hall signal lines must be distinguished. Especially, the power supply lines must not be mistaken. The sequence on the board must match the sequence of the three phase lines on the motor driver board to work properly. If you do not know the definition of the Hall wire, you can debug the low voltage and current at the first power on. Change the order of the Hall line until normal operation, do not use large current, high voltage debugging, if the Hall line is not connected in sequence, the high voltage and high current test machine, there is the risk of damage to the MOS tube, if the three Hall signal lines The motor is running smoothly and smoothly. The low-speed start is stable and the torque is large. If the three Hall signal lines are not connected, the following characteristics are available: 1 The motor cannot be started normally or the start-up is difficult (sometimes it is necessary to manually turn the motor to start) 2 The motor starts to shake with no power.Motherboard specifications:Product Name: 450W Brushless Hall DC Motor DriverModel Number: ZS-X11D1Operating voltage: 9-60VMaximum current: rated 16A peak 20AMaximum power: 450WOvercurrent protection: YesProduct size: length 63MM* width 45MM* height 28MMWeight: about 93g.Precautions: 1. The power supply circuit on the main board has no fuse, and the built-in self-addition will cause permanent damage to the chip on the board (even 2 seconds is not allowed).2. During normal operation, there is sampling overcurrent protection at the motor output. Since the module power and current are very large, please do not short circuit when the module is not working normally. Once the short circuit has the possibility of burning the line, the first wiring test machine Please use small current and low voltage test, after ok, then pass high current and high voltage, because it is bare board module for sale, pay attention to the wiring line insulation, strong voltage is not allowed to touch the board parts.3. Do not connect the motor that is obviously inconsistent with the voltage and current of the drive module or is far away from the motor to avoid inexplicable damage. Package Contents:2 set brushless motor controller On Aug 6, 2024 at 23:31:45 PDT, seller added the following information:
This speed regulator is used for DC brushless motor with PWM speed regulating function. PWM Frequency ≈ 20kHz.
1.Usually your Items will be shipped within 1-3 business day after your payment is cleared. International orders may take 10 to 30 business days to arrive. 2.We have CA, NJ warehouses and ship items may vary according to the stock. 3.No shipping on Weekends or US Public Holidays. 1.You can return your unused items back for exchange or refund within 30 days. 2.Please contact us for return process before you return the item. If there is any fault or problem with the product, please dont be shy to express it, we will solve it at the first time. Everything for the customer is our purpose, your positive feedback and 5-star DSR is our greatest support and encouragement! Looking forward to your every purchase! All rights reserved.
Input maximum power: up to 3000W. Any three-phase DC brushless motor with or without Hall, within the range of (panel nominal AC80V~220V), and with low temperature under high current operation. High torque and high speed output, with a maximum speed of 10000rpm/min (depending on the user’s motor).
This product is a driver module developed for non inductive BLDC motors. The chip has the characteristics of simple peripheral circuits, complete functions, small size, easy debugging, high driving efficiency, flexible application, and wide applicability.
Feature: Voltage: 36V/48V Power: 500W Color: Silver Casing Material: Aluminium Soft Low-Voltage: When the battery voltage become lower, the current will also become lower to keep normal running. It not only protect the battery and extend the battery life, but also increase the running distance. Note： this controller only supports three – wire brushless motors and three – wire throttle, not six – wire throttle. Regenerative braking is not supported. Application: .
This product is a driver module developed for non inductive BLDC motors. The chip has the characteristics of simple peripheral circuits, complete functions, small size, easy debugging, high driving efficiency, flexible application, and wide applicability.
Maximum power: 400W. After receiving the goods, there are generally 5 Hall wiring lines on the brushless motor. Two of them are Hall power lines. Three Hall signal lines must be distinguished. In particular, the power cord must not be connected incorrectly.